收藏晋升泰|英文官网|网站地图|晋升泰简介HI,欢迎来到晋升泰精密(深圳)有限公司官方网站!

热门关键词:紧固件生产厂家紧固件定制紧固件紧固件紧固件

强大的客户服务实力
当前位置:首页 > 资讯·技术 > 紧固件资讯 »>>汽车车牌安装专用螺丝,安防不锈钢螺丝

汽车车牌安装专用螺丝,安防不锈钢螺丝

文章出处:人气:0发表时间:2017-10-27【 返回列表

汽车车牌安装专用螺丝,安防不锈钢螺丝。Car license plate installation of special screws, security, stainless steel screws.汽车车牌是国家车辆管理法规规定的具有统一格式、统一式样,由车辆管理机关经过申领牌照的汽车进行审核、检验、登记后,核发的带有注册登记编码的硬质号码牌。Car license plate is a national vehicle management regulations with a unified format, unified style, by the vehicle management authority through the license plate of the vehicle for review, inspection, registration, issued with a registration code with the hard number plate.一般为两面,分别按规定安装在汽车前后部指定位置上。汽车号牌是准许汽车上道行驶的法定凭证,是道路交通管理部门、社会治安管理部门及广大人民群众监督汽车行驶情况,识别、记忆与查找的凭证。Usually on both sides, respectively, according to the provisions of the car installed in the front and rear designated location. The license plate is a legal certificate that allows the car to travel on the road. It is a document that the road traffic management department, the social security management department and the broad masses of the people supervise the automobile driving situation, identify, memorize and find the vehicle.

 

不锈钢螺丝 晋升泰精密(深圳)有限公司.jpg

 

  汽车车牌应该如何安装?How should the car license plate be installed?

 

  使用自攻螺丝+防盗螺栓的安装的优点和缺点。The advantages and disadvantages of using self-tapping screws + anti-theft bolts are installed.

 

  优点:安装牢固,防锈、具有一定的防盗能力。Advantages: installation of solid, rust, with a certain degree of security capabilities.缺点:防盗螺栓需要自行解决,尤其是不锈钢的防盗螺栓、螺母、垫片、弹簧垫均需要不锈钢制造的。安装比较复杂,需要打孔,车要上架子或者上沟道安装。Disadvantages: anti-theft bolts need to solve their own, especially stainless steel anti-theft bolts, nuts, gaskets, spring mats are required to manufacture stainless steel. Installation is more complex, need to punch, the car to the shelf or on the channel to install.

 

安装方法installation method:上面使用自攻螺丝,下面使用防盗螺栓,安装方法与自攻螺丝基本相同,需要说明一点,前面保险杠下面2个不锈钢螺丝位置需要打孔,一定要认真点,原来的位置是给长自攻螺丝用的,有个类似桶状的塑料柱。Above the use of self-tapping screws, the following use of anti-theft bolts, installation methods and self-tapping screws are basically the same, need to explain that the front of the bumper below 2 stainless steel screw position need to punch, be sure to point, the original position is to long Screw, there is a similar barrel of plastic column.上防盗螺栓最好去4s让师傅们帮你弄,要拆掉车前部底下的塑料隔板,然后手伸进去上垫片-弹簧垫-螺母。后面的保险杠比较简单,去掉保险杠上下面的2个涨塞,不锈钢螺丝可以直接伸进去,用手从保险杠内侧上垫片-弹簧垫-螺母即可。The best anti-theft bolts to 4s so that the master to help you get, to remove the car under the front of the plastic partition, and then hand into the gasket - spring pad - nut. Behind the bumper is relatively simple, remove the bumper on the bottom of the two plug, stainless steel screws can be directly into the hand from the inside of the bumper on the gasket - spring pad - nut can be.

 

以上就是晋升泰为您带来的有关不锈钢螺丝的知识,希望对您有所帮助。

快捷通道/ PRODUCTS
非标紧固件
定位销 圆柱销 螺丝/螺栓 衬套 支柱 轴环 螺母 垫圈 浮动接头 小径弹簧柱塞
紧固件资讯
公司新闻 紧固件资讯 常见问题
关于晋升泰
公司环境 激情团队 荣誉证书 展会参展
晋升泰首页|非标定位销|非标圆柱销|非标轴套|常见问题|展会参展|荣誉证书|联系晋升泰|晋升泰简介
'); })();